| ■Product Name |
Exhibition/Demo Unit
Fujikura
Fiber Splicer
FSM-16R, up to 4 cores |
| ■Accessories |
・Instruction Manual
・Monitor Cover
・Power Cord
・AC Adapter
・Charging Cable
・Battery
・Magnifier
・Case
・Key
※All accessories are shown in the photos.
Please note that items not shown in the photos are not included.
●Regarding batteries, rechargeable batteries, parts, and consumables that require replacement:
They are not covered by the initial product defect or operation guarantee. Please arrange for replacements yourself if necessary. Pre
|
|
Fiber splicing is possible for single-core to 4-core fibers.
Applicable fibers: Single-mode (SM), dispersion-shifted (DS), multimode (MM), and non-zero dispersion-shifted (NZ-DS) single-core to 4-core silica fibers
Cladding diameter: 125μm
Fiber coating diameter: Single-core coating diameter 0.25mm, 0.9mm / Multi-core tape thickness 0.25mm to 0.4mm |
| ■Condition |
|
As this is a demo unit, it has been used only a few times and is in excellent condition!!!
■Operation has been confirmed!!
To ensure that customers receive a product in good condition, the following cleaning has been performed before sale.
Cleaning areas
・Exterior cleaning
・Interior cleaning
※The series of operations was confirmed in the state set by the previous customer, so the purchaser needs to enter their own settings after the product arrives.
※Professional knowledge is required for use.
We sell products, but support and explanations are not included in the price.
This product is sold as-is.
Therefore, it is sold without an operation guarantee.
Please purchase on a no-claim, no-return basis.
※The product is delivered in the condition shown in the photos, so please purchase only if you are satisfied.
|
|
| Applicable fiber |
Single-mode (SM), dispersion-shifted (DS), multimode (MM), and non-zero dispersion-shifted (NZ-DS) single-core to 4-core silica fibers |
| Cladding diameter |
125μm |
| Fiber coating diameter |
Single-core coating diameter 0.25mm, 0.9mm / Multi-core tape thickness 0.25mm to 0.4mm |
| Clamping method |
Fixed by fiber holder |
| Fusion splicing method |
Fixed V-groove fusion splicer |
| Actual connection loss |
SM: 0.05dB / DS: 0.08dB / GI: 0.02dB (all standard values) |
| Connection mode |
30 modes (9 connection conditions stored at the factory) |
| Standard connection time |
30 seconds (when fusion splicing 4-core tape) |
| Connection loss estimation function |
Yes |
| Connection pull test |
Tensile strength 1.96N (approx. 200gf) |
| Connection data recording |
Stores the latest 250 connections (discharge conditions, estimated loss values, connection mode, misalignment, end-face angle, comments) in internal memory |
| Automatic discharge intensity correction function |
Supports changes in atmospheric pressure (3500m) |
| Wind resistance |
Maximum allowable wind speed 15m/sec |
| Monitor |
Large 5-inch color monitor |
| Heater for reinforcement sleeve |
Supports both 40mm and 60mm lengths |
| Heating mode |
10 modes (3 heating conditions stored at the factory) |
| Standard time for heating reinforcement |
100 seconds (when heating reinforcing 4-core tape) |
| Power supply |
AC 100-240V 50/60Hz / Slot-in battery (NiCd: DC12V) |
| Standard number of connections per charge |
35 connections / Includes HJS-02 use and heating reinforcement (fully charged) |
| Dimensions and weight |
W150mm x D150mm x H120mm (excluding wind shield) Approx. 2.7kg (including AC adapter) |
|
The shipping area is Kyoto.
■Shipping Fee (Prepaid only)
Flat rate nationwide: 3,200 yen
Shipping to Hokkaido, Okinawa, and remote islands is also the same fee.
※We do not basically offer a combined shipping service.
If you wish to use it, please contact us in advance.
※We insure all shipped products.
If there is any damage, please contact us.
If the damaged part can be repaired, we will provide repair service.
Returns are not accepted. Please note this in advance.
|
●If you wish to receive a receipt, please let us know.
We will respond flexibly to suit your circumstances.
We can issue a set of three documents: an estimate, invoice, and delivery note.
Please provide the detailed information required for issuance (billing address, shipping address, seal date, etc.).
※If required, please contact us in advance.
|
